Catalog Number: T75019453

OEM Number: 059931VC-BX

Industry Part Number: 059931VC-BX

PRODUCT TYPE: Radial Shaft Seal

Seal Profile: WAO

Lip/Base Material: 70 Nitrile Black

Commodity Code: 4016930000

Country of Origin: Taiwan

PRODUCT SPECIFICATIONS

Series: WAO
Type: Single Lip
Inside Diameter: 0.593 Inch
Outside Diameter: 0.935 Inch
Width: 0.175 Inch
Material: 70 Nitrile Black

DESIGN SPECIFICATIONS

Without tension spring
Without protective lip
Rubberized outer jacket
Sealing material: NBR, FKM
Material stiffening plate: Unalloyed steel DIN EN 10139 (DIN 1624)

FUNCTION

Dynamic sealing of rotating shafts, independent of direction of rotation
Rubberized outer jacket ensures tight fit and seal to housing bore
Only limited static sealing between sealing lip and shaft at standstill

PRODUCT ADVANTAGES

Good static sealing effect with low-viscosity or gaseous media
Low friction
Compensates for thermal expansion, e.g. in light metal housings, good sealing effect with greater roughness and with split housings
Long service life
Reliable design with broad application spectrum for moderately demanding applications in general industry

COMMON APPLICATIONS

Sealing against grease
Subordinate seals, e.g. as dust, dirt or splash protection seals for electric motors

APPLICATION LIMITS

Pressure [Mpa]: max. 0
Peripheral speed [m/s]: max. 6
The values given here are maximum values and may not all be reached at the same time
NBR

Temperature [°C]: -40 to 80, short-term up to 100

FKM

Temperature [°C]: -25 to 150

MEDIA RESISTANCE
NBR

Good chemical resistance to various mineral oil and greases (H, HL, HLP)
Flame-retardant hydraulic fluids HFA and HFB, HFC up to appr. +50°C
Water up to max. +60°C
Low resistance to ozone, weathering and ageing

FKM

Good chemical resistance to mineral oils and greases, synthetic oils and greases, engine, gearbox and ATF oils up to approx. +150 °C
Fuels, flame-retardant pressure fluids HFD, aliphatic, aromatic and chlorinated hydrocarbons
Water up to max. +60°C
Very good resistance to ozone, weathering and ageing

DESIGN GUIDELINE

Design of the installation space is recommended in accordance with DIN 3760
Roundness of shaft - tolerance class IT8 - free of twists, burrs and damage of any kind
Shaft surface roughness Rz = 1.0 to 4.0 ?m
Hardness of shaft surface min. 45 HRC
Housing surface roughness Rz = 10 to 20 ?m
Shaft tolerance zone: ISO h11
Housing tolerance zone: ISO H8

INSTALLATION GUIDELINE

Clean the installation space carefully before installation, remove dust, dirt, metal chips, etc
Do not pull the seal over sharp edges, threaded tips or cavities (feather key grooves) during installation, cover with a mounting sleeve if necessary
Do not grease the seal or installation space for assembly
Careful installation on the shaft, tilting is not permitted

STORAGE ADVISE

Storage temperature <25°C
No direct heat sources
No direct sunlight
No condensation in the storage room
No exposure to ozone or ionizing radiation
Recommendations based on the revision of ISO 2230 dated 16.09.1992

In mechanical equipment, oil seals, also known as grease, fluid, or dirt seals, help keep lubricant from escaping by sealing the gaps between moving and stationary parts. Oil seals are essential parts of almost every kind of equipment and vehicle in use and have optional metric and inch shaft and bore sizes. To produce a tight seal, the sealing lipwhich is frequently composed of rubber or elastomerspresses up against the rotating shaft. Oil seals have optional single lip, double lip and triple lips. Depending on the temperature and chemical resistance requirements of the application, materials such as silicone rubber, nitrile rubber, or fluorocarbon are employed. Oil seals are relatively simple to install and replace, minimizing downtime for maintenance. Maxtran stocks both rubber covered and fully metal options for better structural support and to help secure the seal within the housing. Maxtran. com is the Worlds largest Authorized TCM oil seal distributor offering over 150,000 shaft and bore sizes and sealing lip configurations in various materials for every industrial and automitive application. Every single WAO Series Single Lip American Chain 3123668 Oil Seal includes free same-day shipping and concierge technical support. This 3123668 oil seal is manufactured from 70 Nitrile Black material and has a 0. 593 Inch shaft diameter and 0. 935 Inch bore diameter and is 0. 175 Inch thick. With so many oil seal size options Maxtran is the #1 choice for buying shaft seals in the USA!

MAXTRAN® offers a 30-Day, 100% Quality Guarantee Against Material and Manufacturing Defects Only, No Exceptions. All Claims must be made within 72-Hours of receiving your parts. MAXTRAN® is not responsible for Shipping Carrier damage or lost shipments. It is the customers responsibility to file a claim with the shipping carrier. No additIonal or implied warranties for this product are offered by MAXTRAN®. An RGA is required for all returns. We do not offer refunds without a replacement order of equal or greater value from the original order. If products are out-of-stock when a replacement is needed a store credit will be issued. Returns are only allowed for manufacturing defects and product damage. A 30% Restock Fee will be charged for all approved returns unless the product is dispositioned to be defective by our Quality Manager . All Shipping is non-refundable and any return shipping to our warehouse is the customers responsibility.